enginehistory.org Forum Index enginehistory.org
Aircraft Engine Historical Society Members' Bulletin Board
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

I don't think this is the recommended procedure.

 
Post new topic   Reply to topic    enginehistory.org Forum Index -> Book, Mags, Films, Recordings, Reference
View previous topic :: View next topic  
Author Message
rwahlgren



Joined: 15 Aug 2003
Posts: 324

PostPosted: Sun Jul 20, 2008 11:49    Post subject: I don't think this is the recommended procedure. Reply with quote

http://www.youtube.com/watch?v=vS_jdXVzT58&feature=related

http://www.youtube.com/watch?v=Xx7N9nibD0c

http://www.youtube.com/watch?v=K1J-8q25TTo&feature=related

http://www.youtube.com/watch?v=fOIAk6CK_uY&feature=related


So I see one tank, Gas??? What about oil??? Not much for cooling it.
Looks like he extended the rear sump and that is it for oil.
Back to top
View user's profile Send private message
jschauer



Joined: 19 May 2004
Posts: 93
Location: Justin, Texas

PostPosted: Sun Aug 10, 2008 16:11    Post subject: Reply with quote

It would run better if he had a little more fly wheel than a prop hub, but at least he got it running.
Back to top
View user's profile Send private message
rwahlgren



Joined: 15 Aug 2003
Posts: 324

PostPosted: Sat Aug 16, 2008 17:26    Post subject: Reply with quote

I don't think flyweight is that important when going through a transmission. The crankshaft, its weights and the master rod assemblies will pretty much be the flyweight.
I think his main problems are, not enough prime, he doesn't seem to open the throttle enough, its not getting enough fuel, I was going to say ignition boost too, but not sure about the high tension engines. I know the low tension engines need ignition boost for start. His method of prime is to dump gas down the carburetor. And start at idle throttle setting. He needs to be priming as it is turning, not stop and walk up and dump some gas and run away from it and then turn it over.
Back to top
View user's profile Send private message
jschauer



Joined: 19 May 2004
Posts: 93
Location: Justin, Texas

PostPosted: Thu Aug 21, 2008 08:02    Post subject: Reply with quote

The fly wheel would at least keep it spinning in between cylinder firings. Crazy way to prime! Just waiting for a backfire....
Back to top
View user's profile Send private message
rwahlgren



Joined: 15 Aug 2003
Posts: 324

PostPosted: Thu Sep 11, 2008 20:48    Post subject: Reply with quote

Actually unloaded fly weight would not be good on the reduction assembly.
As it would violently take up backlash in coast then in power, that is if there was enough time, if not then it would act like no flyweight at all.
A dynamometer or propeller adds a load to the gear set and that load would actually oppose inertia effect from the flyweight. Running a flyweight through a gear set is not the same as a direct connection to the crankshaft. If you have ever held/seen the master/ articulated rod/ piston assemblies that are attached to the crank pin and then in a Wasp Major times that by 4 you will see there is more than sufficient flyweight in that engine.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    enginehistory.org Forum Index -> Book, Mags, Films, Recordings, Reference All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group