![enginehistory.org Forum Index](templates/subSilver/images/logo_phpBB.gif) |
enginehistory.org Aircraft Engine Historical Society Members' Bulletin Board
|
View previous topic :: View next topic |
Author |
Message |
jgertler
![](images/avatars/2243286443f3a8d1170500.jpg)
Joined: 13 Jul 2003 Posts: 9
|
Posted: Wed Aug 13, 2003 15:23 Post subject: pre-WWII church racing engine |
|
|
Here is an unusual Pre-War racing engine, built by Jim Church for the Church mid-wing racer in the National Air Races. Allow me to point out some novelties. He cast his own cylinders (did not use Heath cylinders). It would appear that this engine had permanent carb. heat, as the intake goes from carb at bottom of oil sump-Through cast tube inside of the aluminum oil sump and out again to the side manifold. The surrounding oil would have kept the intake air on the warm side. For a plane and engine of this size (dubiously listed at 41 HP -about 30% more than a Heath) the use of streamlined exhausts made from a separate pieces of steel streamlined strut tubing for each cyl. always made me smile. Last year I donated this engine to Seattle Museum of Flight, along with a much needed factory-built Heath B-4 and 30 other rare engines. Should be on display there, shortly. see at:
http://members.cox.net/barnstormer1/churchl.jpg |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
gwhite
Joined: 13 Jul 2003 Posts: 58
|
Posted: Wed Aug 13, 2003 16:14 Post subject: Re: pre-WWII church racing engine |
|
|
jgertler wrote: | Here is an unusual Pre-War racing engine, built by Jim Church for the Church mid-wing racer in the National Air Races. Allow me to point out some novelties. He cast his own cylinders (did not use Heath cylinders). It would appear that this engine had permanent carb. heat, as the intake goes from carb at bottom of oil sump-Through cast tube inside of the aluminum oil sump and out again to the side manifold. The surrounding oil would have kept the intake air on the warm side. For a plane and engine of this size (dubiously listed at 41 HP -about 30% more than a Heath) the use of streamlined exhausts made from a separate pieces of steel streamlined strut tubing for each cyl. always made me smile. Last year I donated this engine to Seattle Museum of Flight, along with a much needed factory-built Heath B-4 and 30 other rare engines. Should be on display there, shortly. see at:
http://members.cox.net/barnstormer1/churchl.jpg |
I'd never even heard of the "Church" engine. It jsut amazes me thta so many folsk wer out ther building engines. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
jgertler
![](images/avatars/2243286443f3a8d1170500.jpg)
Joined: 13 Jul 2003 Posts: 9
|
Posted: Wed Aug 13, 2003 16:38 Post subject: |
|
|
I forgot to list the specific name for this engine. Just as heath made a lot of different types of Henderson conversion parts for homebuilders-and listed their Own factory built engine as the B-4...Jim Church also modified a number of Hendersons with Heath parts before deciding he could design a better conversion. The Church built engine was called a J-3 Marathon. I was told he built only three of them, but I suspect there were more. I think this one is the only one known to survive. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
UAHArchives
Joined: 13 Jul 2003 Posts: 4
|
Posted: Fri Jan 23, 2004 16:08 Post subject: |
|
|
In reguard to the Church radial engine. There were suveral Ford Engines that had Church Modifications to them. Does any one know if this is the same church? |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|