enginehistory.org Forum Index enginehistory.org
Aircraft Engine Historical Society Members' Bulletin Board
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

A question about manifold pressure

 
Post new topic   Reply to topic    enginehistory.org Forum Index -> Collections/Restorations - General
View previous topic :: View next topic  
Author Message
bhazel



Joined: 16 Oct 2004
Posts: 2
Location: Imperial Beach CA

PostPosted: Mon Oct 18, 2004 20:00    Post subject: A question about manifold pressure Reply with quote

Hello all,
I would like to understand manifold pressures a bit better. I am familiar with automotive manifold pressures, which are always measured in pounds per square inch. Aviation engines list pressures in inches of mercury.
Does anyone know how the 2 relate?
Thanks a million,
Ben
Back to top
View user's profile Send private message
kmccutcheon



Joined: 13 Jul 2003
Posts: 298
Location: Huntsville, Alabama USA

PostPosted: Tue Oct 19, 2004 08:41    Post subject: Reply with quote

Quote:
I am familiar with automotive manifold pressures, which are always measured in pounds per square inch. Aviation engines list pressures in inches of mercury.
Does anyone know how the 2 relate?


29.92 inches of mercury (inHg) = 14.7 psi

Aircraft manifold pressure measurements are absolute. In other words, an aircraft manifold pressure gage will, on a standard day at sea level, read 29.92 inHg when the engine is not running. With the engine at idle, it may read 4 or 5 inHg. A normally aspirated engine will read about 28-29 inHg at sea level with the throttle wide open (the difference is due to losses in the induction system). A supercharged engine can greater than atmospheric pressure. Some racing aircraft engines run at manifold pressures approaching 150 inHg.
_________________
Kimble D. McCutcheon
Back to top
View user's profile Send private message Visit poster's website
bhazel



Joined: 16 Oct 2004
Posts: 2
Location: Imperial Beach CA

PostPosted: Tue Oct 19, 2004 16:43    Post subject: Reply with quote

OK.
If 29.92 inches of mercury (inHg) = 14.7 psi, then if I measured the manifold pressure on that motor 150 inHg in psi, I would see about 5 times atmospheric, or 73.5psi???
I am an auto shop teacher, and I often relate current auto technology ie 4 valves per cylinder, dual cams, fuel injection, turbochargers etc to the older motors where they were actually new stuff.
They all understand boost numbers in psi, and I'd love to be able to show them boost numbers that they can relate to from what I've read about Reno racers and other 60 year old motors.
Thanks,
Ben
Back to top
View user's profile Send private message
kchristensen



Joined: 22 Nov 2004
Posts: 1

PostPosted: Fri Nov 26, 2004 09:00    Post subject: Reply with quote

I'm a shop teacher myself. I am, at present, teaching kids in Grades 6-7-8. I'm engendering interest and conversation with them this year by building a 1/2 scale Axial prop for a Fokker DR-1 and a replica Eindecker wing for the wall.

When I taught high school and explained that all IC engines operate by the same physics and that Honda didn't invent variable valve timing, dual overhead cams, pentroof combustion chambers, etc. I'm met with slack jaws. I go further to point out all those things were first invented around WW1, the amazement is palpable. I also liked pointing out that multi-stage compressors were commonplace in the 30s and 40s, when single stage forced induction isn't that common on cars, even today.

Cheez,

F=MA
Back to top
View user's profile Send private message
tmcdaid



Joined: 03 Feb 2004
Posts: 9

PostPosted: Tue Dec 14, 2004 17:32    Post subject: Reply with quote

An acceptable approximation in many cases is that 1 psi is approximately equal to 2" Hg and (the old math teacher in me shudders). While Kim's numbers above are much more accurate, very roughly, standard sea level atmospheric pressure is about 15 psi or 30" Hg. So, remembering that in automotive use, "boost" general means manifold gauge pressure, or pressure in excess of atmospheric pressure while normal aircraft usage is to refer to absolute manifold pressure (MAP), you can do the 2:1 conversion, remembering to add or subtract atmospheric pressure as required. Examples:

My F-150 Lightning will develop 8 pounds (more correctly, psi) boost, which would be 16" boost or 46" (16 + 30) MAP.

In Kim's example of an aircraft engine developing 4" pressure at idle, that's about 2 pounds absolute pressure, or 15-2=13 psi of vacuum.

In Kim's racing engine example, 150" manifold pressure in a racing aircraft engine is about 75 psi absolute pressure, or 60 (75-15) psi boost.

I typed that pretty quickly. I think I did it all correctly, and hopefully that gives a feel for the comparison. You can do some easy (or lesss easy looking if you use more accurate numbers) formulas, but I have always preferred to understand the relationship and go through that way. If someone would like, I'll spend a few minutes and figure out a few formulas (there would really be one equation with some algebraic variations on it).

Cheers!
_________________
Tim McDaid
Back to top
View user's profile Send private message Send e-mail
szielinski



Joined: 13 Jul 2003
Posts: 94
Location: Canberra, Australia

PostPosted: Thu Dec 16, 2004 01:28    Post subject: Reply with quote

Perhaps www.onlineconversion.com/pressure.htm can assist for the web-enabled young 'uns.
Back to top
View user's profile Send private message Send e-mail
jjuutinen



Joined: 13 Jul 2003
Posts: 180

PostPosted: Sat Dec 18, 2004 05:28    Post subject: Reply with quote

I have a follow up question. Some charts and folks claim that the unit used by Germans , i.e. ata refers to "technical atmosspeher", i.e. 1 ata=1 bar. However, one Finnish guy who know aero engines, says that the ata refers to normal atmosphere, i.e. 1 ata=1.01325 bar. I´d agree with the latter. Anyone better informed?
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    enginehistory.org Forum Index -> Collections/Restorations - General All times are GMT - 6 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group